一、三葉羅茨風機如何組裝？針對“組裝”的問題，我們要了解組裝的內容，三葉羅茨風機出廠前的組裝有兩部分內容，一分部是機頭的組裝，一部分是整機的組裝，這些是出廠前的組裝；經過組裝之后，便可以進行發貨了，終端客戶在拿到三葉羅茨風機之后，還會對羅茨風機進行管道與風機的連接。

1、 How to assemble a three leaf Roots blower? Regarding the issue of "assembly", we first need to understand the content of assembly. The assembly of the Three Leaf Roots blower before leaving the factory consists of two parts: one is the assembly of the machine head, and the other is the assembly of the entire machine. These are the assembly before leaving the factory; After assembly, it can be shipped, and the end customer will also connect the pipeline to the Roots blower after receiving it.

下面風機針對出廠前的風機組裝進行詳細的描述：三葉羅茨風機安裝的時候需要注意什么問題?

Below is a detailed description of the fan assembly before leaving the factory: What should be paid attention to when installing the Three Leaf Roots blower?

1、機頭安裝

1. Head installation

風機的機頭為組裝好的，將組裝好的風機機頭安裝在底座的一側，然后使用螺栓進行緊固；

The fan head is assembled, and the assembled fan head is installed on one side of the base, and then fastened with bolts;

2、電機安裝

2. Motor installation

電機安裝在底座的另一側，安裝上去之后，對螺栓稍加緊固，不要立即緊固鎖死；

The motor is installed on the other side of the base. After installation, tighten the bolts slightly and do not immediately tighten and lock them;

3、皮帶輪安裝

3. Belt pulley installation

皮帶輪有兩部分，一個安裝在機頭一側，一個安裝在電機一側，使用設備，對皮帶輪進行調整，在裝配時，必須要保證機頭和電機的皮帶輪，在一條縱向線上，不能出現偏差，要調整到在同一水平面上；

The pulley has two parts, one installed on the side of the machine head and the other on the side of the motor. Professional equipment is used to adjust the pulley. During assembly, it is necessary to ensure that the pulleys of the machine head and the motor are on the same longitudinal line, without deviation, and adjusted to the same horizontal plane;

4、皮帶安裝

4. Belt installation

安裝好皮帶輪之后，然后安裝皮帶；

After installing the pulley, proceed to install the belt;

5、緊固螺栓

5. Tighten bolts

緊固電機的螺栓，同時調整羅茨風機皮帶的松緊度，調整好之后，然后進行螺栓鎖死緊固；

Tighten the bolts of the motor and adjust the tightness of the Roots blower belt. After adjustment, lock and tighten the bolts;

6、安裝皮帶保護罩

6. Install belt protection cover

上面的安裝完成之后，將皮帶保護罩安裝在底座上面，緊固螺栓即可；

After the installation is completed, install the belt protection cover on the base and tighten the bolts;

7、安裝壓力表閥

7. Install pressure gauge safety valve

一般廠家為了保證壓力表閥不被損壞，可能不會為我們安裝，有的廠家可能會對此進行安裝；

Generally, manufacturers may not install the pressure gauge safety valve for us to ensure that it is not damaged. Some manufacturers may install it instead;

本文來自：羅茨風機更多的內容請點擊：http://www.hy579.cn我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

This article is from Roots blower. For more content, please click: http://www.hy579.cn We will provide satisfactory service for the questions you ask. Welcome to call us!